CRAFTERS CHOICE GEMS & BEADS KEY CHARM

Crafters Choice Gems & Beads Key Charm Project

Instructions

Pro-Tips for E6000

Ventilation: E6000 is powerful stuff—always work in a well-ventilated area.

Cure Time: While it "tacky-sets" quickly, wait a full 24 to 72 hours before using the keyring to reduce the chance of gems coming loose.

Cleanup: If you get a "string" of glue on your sparkly mesh, wait for it to dry slightly and then roll it off with your finger - it's easier than trying to wipe it while wet!




Acrylic Disk

  1. Remove the protective film from one side of the acrylic disk, leaving the other side covered while working to protect the surface from any scratches or glue.
  2. Select a design from provided template or create your own. Print the Template out at 100% scale and tape the disk over the selected design, lining up the small circle at the top with hole in the disk. Ensure the tape does not cover any part of the design.
  3. Place the rhinestones onto the disc to preview your placement and colour scheme.
  4. Once you are happy with your design, remove the gems carefully from disk surface, keeping different colours and sizes separate for easy application.
  5. Starting on the outline of the design, apply a small amount of E6000 adhesive to the disc and use a toothpick to spread it out into a smooth, thin layer. Cover roughly 2cm2 of space at a time so that the glue doesn't set before you add the rhinestones.
  6. Use your applicator to pick up the rhinestones and press them onto the glue. They will not set right away, so you will have some time to adjust as needed. Work your way around the design in small sections. Using a combination of small and large gems can help to fill in the space and add dimension.
  7. When you are happy with the design and application, set aside to fully dry. E6000 will take 24-72 hours to fully set and dry.
  8. Once set, remove the protective film from the back of the disc.

Beaded Loop

  1. Unwind a portion of jewellery wire. Don't cut it yet, as the spool will help to hold the beads in place while you working.
  2. Thread on the round beads in your chosen colour design. Mix and match colours and sizes until you are happy with the look.
  3. When the beaded length reaches approximately 21cm, measure out another 10cm of wire and cut it using your pliers.
  4. Take both ends of the wire and thread one crimper through both pieces of wire. Thread on a jump ring then thread the wire back down the crimper and pull tight. Use pliers to close the crimper and secure the wire.
  5. Finish off the end by threading the tail of the wire back through the beads to conceal the end.

Alphabet Bead Chain

  1. Decide on your chosen word and bead placement. Placing a round bead between each letter creates a more dynamic design and holds the letters in place more securely on the wire.
  2. Once you are happy with your design, measure out a piece of wire that is about 6cm longer than your design. L-O-V-E was 12cm, therefore 18cm of wire is cut. At one end, thread on a small bead, then a crimping bead, loop about 3cm of the wire back through the small bead, securing the crimp in place. If the bead passes over the crimp, you may need to select one with a smaller hole first. Once this is in place, use the pliers to close the crimping bead.
  3. Continue threading on your beads, starting at the bottom of your design/the last letter and work your way up.
  4. Once you have threaded on all the beads, finish with a crimping bead, then a jump ring. Thread the remaining wire back through the crimp and pull it tight before closing the crimping bead shut with pliers. Thread the excess wire back down the beads to hide the tail.

Assembly

  1. Using pliers, open the bottom chain link on the keyring and remove it from the chain.
  2. An easy way to do this is to take 2 flat nose pliers and grip the ring on both sides of the opening. Gently twist your wrist in the opposite directions, pulling one towards you and one away from you. To close the link, twist the ends back together till the ends meet flush and secure.
  3. Thread the acrylic disc onto the link, then attach it to the top link on the keyring chain. Gently close the link with your pliers, ensuring it is secure.
  4. Open up the same link you just attached the disc to and attach the bead loop using the jump ring. Position this on the opposite side of the chain to the disc to help it to sit nicely. Gently close this link.
  5. Open the new last chain link and thread on the Alphabet Bead Chain using the jump ring. Gently close it with your pliers, ensuring it is secure.
altText

BECOME A SPOTLIGHT VIP

Get VIP discounts, attend exclusive events and more